学术
Lundberg对数滚子的热弹流特性及其凸度量的修正
孙浩洋[1] 陈晓阳[2] 刘春浩[2] 杨沛然[3]
[1]青岛大学机电工程学院,山东青岛266071 [2]上海大学轴承研究室,上海200072 [3]青岛理工大学机械工程学院,山东青岛266033
摘 要:
研究了Lundberg对数轮廓滚子的弹流特性，并探讨了不同凸度量对压力分布和膜厚分布的影响．结果表明：在弹流状态下Lundberg对数滚子端部仍略有压力集中，且端部膜厚过薄，应适当增大凸度量；而随着凸度量增大，压力逐渐沿滚子轴线向中部集中而导致载荷分配不均．设计凸度量时应综合考虑润滑油成膜性能与压力分布两方面因素的影响，凸度量存在1个最优取值区间，其上、下限分别由压力分布和膜厚分布所决定．提出的凸度量最佳取值区间比以往相关文献中提出的最佳凸度量更合理并便于工程应用.[著者文摘]
文章出处:
《摩擦学学报》-2008年28卷1期 -68-72页
栏目信息:
分 类 号:
文献标识码:
A
文章编号:
1004-0595（2008）01-0068-05
Study on Thermal EHL Performance of Lundberg Profile Rollers and the Modification of its Crowning Value
SUN Hao-yang, CHEN Xiao-yang , LIU Chun-hao , YANG Pei-ran （1. College of Mechanical and Electronic Engineering, Qingdao University, Qingdao 266071, China; 2. Research Institute of Bearing, Shanghai University, Shanghai 200072, China ; 3. School of Mechanical Engineering, Qingdao Technological University, Qingdao 266033, China）
Abstract:
Rolling contact friction pairs, such as rolling beatings, gears are widely in mechanical engineering, and crowning design should be applied to increase their working performance and service life. Crowning design is currently still mainly based on elastostatic theory, although the effect of applied load was considered, the effects of the velocity and lubricants were ignored. Moreover, the pressure in elastostatic and EHL states is quite different. The EHL performance of Lundberg profile was discovered, and the effect of the crowning value on the pressure as well as film thickness distributions were discussed. Although the pressure ＂edge effect＂ could be considerably avoided, the film thickness ＂edge effect＂ appeared, and satisfactory lubrication state can not constructed. Therefore, the Lundberg profile crowning value was insufficient in EHL state. However, with increase of crowning value, the pressure shifts to the center in axial direction though the film thickness remains thick enough at the edge. The pressure and film thickness distribution should be considered at the same time in designing suitable crowning. There is an optimum range of the crowning value for a particular working condition. The lower bound of the optimum range is mainly decided by the film thickness, while the upper limit of it is mainly decided by the pressure distribution. Compared with the ＂optimum crowning value＂ proposed in former researches, the ＂optimum range of the crowning value＂ proposed currently is more reasonable and convenient to be applied in industry.[著者文摘]
Key words:
EHL, finite line contact, crowning design
基金资助:
青岛大学人才引进启动基金资助项目;上海汽车工业科技发展基金资助项目（0320）;国家自然科学基金资助项目（50575108）.
更多>>免费文章
cqvip.com